Deicing holdover time isn’t one number: 30 minutes to 12 hours

Published:

Holdover time is the window between the start of an aircraft’s final deicing or anti-icing application and the moment it must be airborne. It is not one number. Under FAA guidance, the same active-frost condition gives a Type I fluid 45 minutes on an aluminum wing and 35 minutes on a composite one, while a Type IV fluid in that weather can run to 12 hours — or as little as 30 minutes for a diluted Type III.

Which figure applies depends on the fluid type, its dilution, the outside air temperature, the surface material, and the precipitation. Once the window closes, the aircraft cannot legally depart until it passes a contamination check or is treated again.

Every winter, somewhere on a snowy ramp, a pilot finishes a deicing pass and starts a clock. Passengers see a truck, some steam, and a delay. What they can’t see is that the aircraft now has a legally defined window — and that window might be half an hour or most of a working day.

That window is called holdover time. It runs from the start of the final application of deicing or anti-icing fluid to the moment the aircraft must be airborne. Miss it, and the aircraft is no longer known to be clean in the eyes of the regulations.

The reason this trips people up is that “deiced” sounds like a state. It isn’t. It’s a countdown, and the length of that countdown is set by a table most passengers will never see.

Why the same weather produces wildly different countdowns

Four variables do most of the work: the fluid type, how much water it has been diluted with, the outside air temperature, and the precipitation falling at the time.

Precipitation intensity matters because each published range is bracketed: the top figure applies to light precipitation, the bottom figure to heavy. In some heavy-precipitation conditions the table publishes nothing at all, and the operator has to fall back on its own approved procedures.

Dilution is the variable passengers never think about. Anti-icing fluids are often mixed with water before application, and the mix changes the window dramatically. In the Federal Aviation Administration‘s active-frost table, an undiluted Type IV fluid at or above -1°C gives 12 hours.

Cut that fluid to a 50/50 mix, and the same weather gives 3 hours.

Then there is the surface itself. Composite material sheds heat faster than metal does, so the residual warmth from heated fluid fades sooner on a composite wing. The FAA publishes separate Type I values for the two: 0:45 for aluminum, 0:35 for composite.

Composite-heavy designs such as the Boeing 787 and Airbus A350 feel that split most, though the figure that governs any given flight comes from the operator’s approved program and the fluid table in force at the time.

What each fluid type buys you

Deicing fluids come in four categories, and they are not interchangeable. Type I is a heated deicing fluid — its job is to remove contamination. Types II, III, and IV are anti-icing fluids, applied so they stay on the surface and hold new ice at bay.

Type III is the thin one, formulated for aircraft that rotate at lower speeds. Type IV is the thickest and, in most conditions, the longest-lasting.

Illustrative holdover-time ranges and limits; the crew must use the current fluid-specific table, temperature band, dilution, and aircraft procedures
Condition or rule Type I Type II Type III Type IV
Active frost, OAT at or above -1°C; undiluted fluid 0:45 aluminum; 0:35 composite 8:00 2:00 12:00
Active frost, OAT at or above -1°C; 75/25 fluid-water mixture 0:45 aluminum; 0:35 composite 5:00 1:00 5:00
Active frost, OAT at or above -1°C; 50/50 fluid-water mixture 0:45 aluminum; 0:35 composite 2:00 0:30 3:00
Active frost, below -1°C to -3°C; undiluted fluid 0:45 aluminum; 0:35 composite 8:00 2:00 12:00
Active frost, below -1°C to -3°C; 75/25 fluid-water mixture 0:45 aluminum; 0:35 composite 5:00 1:00 5:00
Active frost, below -1°C to -3°C; 50/50 fluid-water mixture 0:45 aluminum; 0:35 composite 1:30 0:30 3:00
Active frost, below -3°C to -10°C; undiluted fluid 0:45 aluminum; 0:35 composite 8:00 2:00 10:00
Active frost, below -3°C to -10°C; 75/25 fluid-water mixture 0:45 aluminum; 0:35 composite 4:00 1:00 5:00
Active frost, below -10°C to -14°C; undiluted fluid 0:45 aluminum; 0:35 composite 6:00 2:00 6:00
Active frost, below -10°C to -14°C; 75/25 fluid-water mixture 0:45 aluminum; 0:35 composite 1:00 1:00 1:00
Source: Federal Aviation Administration (FAA)

The spread inside a single weather category is the point: in identical active-frost conditions, the shortest Type III value and the longest Type IV value differ by a factor of 24. That gap is set by fluid choice and dilution, not by anything visible from a window seat.

None of these values is a guarantee. Each is a planning figure, and the crew still has to pair it with the required pre-takeoff check.

The NTSB’s investigation of Southern Airways Express Flight 246 shows why a wing that merely looks wet cannot be assumed clean. On January 19, 2024, the flight — a Cessna 208B — departed Dulles, hit vibration and a loss of power soon after takeoff, and came down on a highway. No one was injured.

The investigation turned up contamination on the lift-generating surfaces, and it found that the crew had not performed the required tactile check.

By their reckoning, the aircraft had spent about six minutes taxiing, against a Type I holdover window of 11 minutes. The aircraft was still inside its window — which is exactly why the contamination check, not the clock, was the control that mattered.

Superdeals to Asia preview

Superdeals cover departures from North America, Europe and Australia.

Flight deals most people never see

Air Traveler Club monitors thousands of routes for pricing anomalies that traditional search engines miss. With ATC Superdeals members save up to 80% on each flight vs. regular fares.

Too good to be true? Check it out yourself. It's free.

Newsletter Form

Delivered weekly. Unsubscribe anytime.

How the clock actually starts, and who runs it

The clock starts when the final application of deicing or anti-icing fluid begins — not when the truck pulls away, and not when the aircraft pushes back.

The operator, not the passenger, selects the seasonal table. That choice turns on the weather, the outside air temperature, the fluid type and concentration, the aircraft’s characteristics, and any lowest operational use temperature. The FAA issues the guidance, while the carrier’s approved ground-deicing program sets out who does what and how.

There is no way for a passenger in a seat to confirm the interval, whether by looking out the window or by asking for one generic number.

When the window closes, or the weather turns worse, 14 CFR 121.631 leaves only three routes to a legal departure. A pre-takeoff contamination check can confirm that frost, ice, and snow are absent from critical surfaces; an approved alternative procedure can reach the same finding; or the aircraft can be treated again, which establishes a fresh holdover time. The pre-takeoff check itself must be completed within five minutes before takeoff begins.

What this means for you

None of these rules creates an automatic payout. Their purpose is the safety of the departure, not compensation.

DOT tarmac-delay protections cover long waits on board and your chance to leave the aircraft. EU261 or UK261 eligibility is a separate question, turning on which jurisdiction the flight falls under, how long the delay ran, what caused it, and whether the extraordinary-circumstances tests apply. A deicing delay on its own does not turn into a payable claim.

What you can do is ask the right question. Not “have we been deiced?” — but “what went on last, and how much time is left on it?”

Gate agents may not have the answer. The crew will.

ATC Intelligence

ATC Intelligence is the research division of Air Traveler Club. Backed by 15 years in Asia-Pacific aviation, we don't just report on the regional market; we live and work in it. By pairing AI-driven data with strict human fact-checking, we provide actionable, trustworthy journalism designed to make your trips to Asia smarter and more affordable.

Follow our daily coverage on Google News, Google Discover, and social media.

Key terms

Holdover time
Holdover time is the interval between the start of an aircraft’s final deicing or anti-icing application and the moment it must be airborne. It is set by the fluid type, its dilution, the outside air temperature, the surface material, and the precipitation, and it is read from a seasonal table the operator keeps in force. The window is not a single number for the aircraft — it is a number for the fluid, the temperature band, the dilution, and the surface, which is why two aircraft on the same ramp can be working from different clocks.
Type IV fluid
Type IV is the thickest of the four deicing and anti-icing fluid categories, applied so it stays on the wing and holds new ice at bay. It is an anti-icing fluid rather than a deicing one, meaning it is meant to remain on the surface after application instead of being washed away with the contamination. In the FAA’s active-frost table it holds the longest value of any fluid type, but that lead narrows as the temperature falls and the mix gets weaker.
14 CFR 121.631
14 CFR 121.631 is the U.S. regulation that governs holdover procedures and pre-takeoff contamination checks for Part 121 airline operations. It applies once the maximum holdover time has been exceeded or the weather has deteriorated, and it permits departure in only three situations. Because it is a Part 121 rule, its three departure conditions bind scheduled airline operations rather than every aircraft that gets deiced.
Pre-takeoff contamination check
A pre-takeoff contamination check is the inspection that confirms frost, ice, and snow are absent from an aircraft’s critical surfaces before departure. It is one of three routes to a legal departure under 14 CFR 121.631 once holdover time has run out, alongside an approved alternative procedure and a fresh treatment. It is distinct from the holdover clock: an aircraft can still be inside its window and fail the check, which is why the inspection rather than the timer is the operative control.
Lowest operational use temperature
Lowest operational use temperature is the coldest outside air temperature at which a given deicing or anti-icing fluid is approved for use. It is one of the inputs an operator weighs when selecting the seasonal holdover table that applies to a flight. Because the value is set per fluid, an operator cannot simply reach for the longest-lasting product on a very cold ramp without checking whether it is approved at that temperature.

Questions? Answers.

What happens if the holdover time runs out before takeoff?

Under 14 CFR 121.631, the aircraft can depart only if a pre-takeoff contamination check confirms frost, ice, and snow are absent from critical surfaces, an approved alternative procedure produces the same finding, or the aircraft is treated again and a fresh holdover time is established. That check must occur within five minutes before beginning takeoff.

Does a deicing delay qualify passengers for compensation?

No automatic compensation follows solely from a deicing-related delay. DOT tarmac-delay protections cover long waits on board and the chance to leave the aircraft, while EU261 or UK261 eligibility depends on jurisdiction, delay length, cause, and the extraordinary-circumstances tests that apply.

Why do composite surfaces have shorter Type I holdover times than aluminum?

Metal conducts and retains heat better than composite material, so the warmth carried over from heated fluid dissipates faster on a composite surface. The FAA’s active-frost table gives Type I values of 0:45 for aluminum and 0:35 for composite — a distinction that matters most on composite-heavy designs like the Boeing 787 and Airbus A350.

What did the NTSB conclude about the January 2024 Southern Airways Express Flight 246 icing incident?

The NTSB found contamination on the surfaces that generate lift and noted that the required tactile check had not been carried out by the crew. Investigators calculated the taxi at roughly six minutes against a Type I holdover context of 11 minutes.